百万等级电站锅炉给水泵径向弯叶片空化性能研究
Research of Cavitation Performance of Radial Bending Blade on 1000 MW Boiler Pump

作者: 程道俊 , 胡永海 :上海能源装备有限公司,上海;

关键词: 电站锅炉给水泵径向弯叶片样条函数空化性能Boiler Feed Pump Radial Bending Blade Spline Function Cavitation Performance

摘要: 本文以百万等级超超临界电站锅炉给水泵为研究对象,通过CFD技术对叶片空化性能进行数值研究。提出一种基于样条函数思想的径向弯叶片几何参数设计方法,引入“正弯叶片”和“反弯叶片”两种叶片径向弯曲结构。结果表明:“直叶片”必需空化余量为22.8 m,与试验值误差仅为0.2 m,预测结果具有一定的精度,“反弯叶片”必需空化余量为21.7 m,空化性能最优;“正弯叶片”在叶片进口处压力面最先出现空泡,吸力面空化面积最大,而“反弯叶片”吸力面空化面积最小。

Abstract: Numerical simulation of cavitation performances of 1000 MW ultra-supercritical pressure boiler feed pump was carried out through CFD applications. A new design method of geometric profile parameters based on Spline function was proposed. Two types of radial bending blades were in-troduced, i.e. “Forward Curved Blade” and “Reversed Curved Blade”. Results indicate that the NPSH (net positive suction head) of “Straight Blade” is 22.8 m, then the absolute error is 0.2 m. Compared with “Straight Blade” and “Forward Curved Blade”, “Reversed Curved Blade” has the best cavitation performance, and NPSH is 21.7 m. The vapor generated at pressure surface of “Forward Curved Blade” near the leading edge at first, and the cavitation region of suction surface is the largest, but the “Reversed Curved Blade” is opposite.

文章引用: 程道俊 , 胡永海 (2015) 百万等级电站锅炉给水泵径向弯叶片空化性能研究。 流体动力学, 3, 29-34. doi: 10.12677/IJFD.2015.34004

参考文献

[1] 刘宜, 张文军, 杜杰. 离心泵内部空化流动的数值预测[J]. 排灌机械, 2008, 26(3): 19-21.

[2] Gulich, J.F. (2007) Centrifugal Pumps. Springer, Germany.

[3] 罗先武, 张瑶, 彭俊奇, 等. 叶轮进口几何参数对离心泵空化性能的影响[J]. 清华大学学报(自然科学版), 2008, 48(5): 836-839.

[4] Medvitz, R.B., Kunz, R.F., Boger, D.A., et al. (2002) Performance Analysis of Cavitating Flow in Centrifugal Pumps Using Multiphase CFD. Journal of Fluids En-gineering, 124, 377-383.
http://dx.doi.org/10.1115/1.1457453

[5] 王伟, 流世炳, 陈涛, 等. 新型无阀微泵扩张微流道中流体动力学特性的仿真分析[J]. 工程设计学报, 2005, 12(4): 223-226.

[6] 王仲奇, 郑严. 叶轮机械弯扭叶片的研究现状及发展趋势[J]. 中国工程科学, 2000, 2(6): 40-48.

[7] 邓小刚, 宗文刚, 张来平, 等. 计算流体力学中的验证与确认[J]. 力学进展, 2007, 37(2): 279-288.

分享
Top