加工工艺及热处理对钛合金板材织构影响的研究现状
Research Situation on the Effect of Manufacturing Process and Heat Treatment on the Titanium Alloy Sheet Texture

作者: 刘松良 :海军驻沈阳地区航空军事代表室,辽宁 沈阳; 卢影锋 , 沙春鹏 :沈阳飞机工业(集团)有限公司,辽宁 沈阳; 黄先明 , 邢秋丽 , 唐 进 :西部钛业有限责任公司,陕西 西安;

关键词: 钛合金板材织构Titanium Alloy Plate Texture

摘要:
织构现象普遍存在于钛合金的生产加工过程中,并已成为钛合金加工方面的研究热点。本文从热轧、冷轧以及热处理制度三个方面分别介绍了近年来钛合金板材织构的研究概况,表明国内外钛合金板材织构研究的方向有较大的差异,而且国内对钛合金板材的织构研究仍较为粗浅,而国外的研究大部分为相变过程中的织构演变。

Abstract: Texture is widespread in the production and the process of titanium alloy, which has become the focus of titanium alloy process research. This paper introduced the researches of titanium alloy plates’ texture in recent years respectively in terms of hot-rolling, cold-rolling and heat-treatment, which suggested that the research direction of titanium alloy plate texture has some differences at home and abroad. The domestic research on the texture of titanium alloy plate is still relatively shallow, while the foreign research mostly studies on the texture evolution in the process of phase transition.

文章引用: 刘松良 , 卢影锋 , 黄先明 , 沙春鹏 , 邢秋丽 , 唐 进 (2015) 加工工艺及热处理对钛合金板材织构影响的研究现状。 冶金工程, 2, 144-150. doi: 10.12677/MEng.2015.23021

参考文献

[1] 毛卫民, 张新明 (1993) 晶体材料织构定量分析. 冶金工业出版社, 北京.

[2] Glavicic, M.G., Kobryn, P.A., Bi-eler, T.R., et al. (2003) A method to determine the orientation of the high-temperature beta phase from measured EBSD data for the low-temperature alpha phase in Ti-6Al-4V. Materials Science and Engineering A, 346, 50-59.
http://dx.doi.org/10.1016/S0921-5093(02)00535-X

[3] Glavicic, M.G., Miller, J.D. and Semiatin, S.L. (2006) A method to measure the texture of secondary alpha in bimodal titanium-alloy microstructures. Scripta Materialia, 54, 281-286.
http://dx.doi.org/10.1016/j.scriptamat.2005.09.016

[4] Germain, L., Gey, N., Humbert, M., et al. (2008) Texture heterogeneities induced by subtransus processing of near α titanium alloys. Acta Materialia, 56, 4298-4308.
http://dx.doi.org/10.1016/j.actamat.2008.04.065

[5] 李兴无, 路民旭, 沙爱学, 等 (2008) 退火温度对Ti-3Al-4.5V-5Mo钛合金显微组织和织构的影响. 稀有金属, 2, 144-150.

[6] Leyens, C. and Peters, M. (2005) Ti-tanium and titanium alloys. Chen, Z.H., Trans., Chemical Industry Press, Beijing, 21.

[7] 尤振平, 惠松晓, 叶文君 (2012) TC4钛合金轧板的织构对力学性能影响. 稀有金属, 1, 31-35.

[8] 李成铭, 李萍, 赵蒙, 等 (2014) TA15钛合金的热变形微观组织与织构. 中国有色金属学报, 1, 91-96.

[9] Hasegawa, M., Yamamoto, M. and Fukutomi, H. (2003) Formation mechanism of texture during dynamic recrystallization in γ-TiAl, nickel and copper examined by microstructure observation and grain boundary analysis based on local orientation measurements. Acta Materialia, 51, 3939-3950.
http://dx.doi.org/10.1016/S1359-6454(03)00218-0

[10] Cottam, R., Robson, J., Lorimer, G., et al. (2008) Dynamic recrystallization of Mg and M-Y alloys: Crystallographic texture development. Materials Science and Engineering: A, 485, 375-382.
http://dx.doi.org/10.1016/j.msea.2007.08.016

[11] Kou, H.C., Chen, Y., Tang, B., Cui, Y.W., Sun, F., Li, J.S. and Xue, X.Y. (2014) An experimental study on the mechanism of texture evolution during hot-rolling process in a β titanium alloy. Journal of Alloys and Compounds, 603, 23-27.
http://dx.doi.org/10.1016/j.jallcom.2014.03.070

[12] Hasegawa, M. and Fukutomi, H. (2002) Microstructural study on dynamic recrystallization and texture formation in pure nickel. Materials Transactions, 43, 1183-1190.
http://dx.doi.org/10.2320/matertrans.43.1183

[13] Schmitt, J.H., Fernandes, J.V., Gracio, J.J. and Vieira, M.F. (1991) Plastic behaviour of copper sheets during sequential tension tests. Materials Science and Engineering: A, 147, 143-154.
http://dx.doi.org/10.1016/0921-5093(91)90840-J

[14] Guorao, N.P., Sethuraman, S. and Satyam, S. (2012) Evolution of texture and microstructure in commercially pure titanium with change in strain path during rolling. The Minerals, Metals & Materials Society and ASM International, 44, 1497-1507.

[15] 朱知寿, 顾家琳, 陈南平 (1994) 钛的织构控制方法与力学性能各向异性的研究. 机械工程材料, 6, 8-10

[16] Nourbakhsh, S. and O’Brien, T.D. (1988) Texture formation and transition in cold-rolled titanium. Materials Science and Engineering, 100, 109-114.
http://dx.doi.org/10.1016/0025-5416(88)90245-5

[17] 朱知寿, 顾家琳, 陈南平 (1995) 冷轧变形量对钛板材再结晶织构形成的影响. 材料科学与工艺, 2, 49-52.

[18] 朱知寿, 顾家琳, 陈南平, 杨照苏 (1994) 钛的织构与力学性能各向异性关系研究. 机械工程材料, 2, 23-25.

[19] 于振涛, 周廉, 邓炬, 顾海澄 (2000) Ti-2Al-2.5Zr合金管、板材织构研究. 稀有金属材料与工程, 2, 86-89.

[20] 江先锋, 向顺华, 陈乃录 (2011) 退火工艺对冷轧纯钛带再结晶织构的影响. 材料热处理技术, 18, 167-169.

[21] 王环, 武保林, 杜兴蒿, 徐前刚 (2008) 不同条件热处理后Ti-15-3钛合金的再结晶织构. 机械工程材料, 11, 20- 24.

分享
Top