喷射流的变化对喷丸强度的影响
Influence of Shot Stream Change on Shot Peening Intensity

作者: 张 立 , 陈再良 :苏州大学,江苏 苏州 ;

关键词: 喷丸喷射流强度位置角度时间Shot Peening Shot Stream Intensity Position Angle Time

摘要:
强度是影响喷丸效果的一个重要因素,而喷射流的改变是强度变化的决定因素。喷射流的不同导致了丸粒平均喷射强度的不同。造成这种差异的主要原因很容易理解,取决于:丸粒型号,速度和密度。这些参数中任何一个值的独立增加都将会使平均喷射强度增加。这种强度的增加对于一个单独的某一时间的喷射流是很好理解的,然而在不断的,持续喷射的情况下,作为一个变量时这种可变性会让人觉得难以理解。通过研究分析得出结论,这种喷射强度的可变性源于饱和曲线,它取决于三大因素:位置,角度和时间。在任何喷丸强化处理的过程中必需对每股喷射流,从位置,角度,和时间上进行严格控制。

Abstract: Intensity is playing a key role in shot peening process, and the change of shot stream is the decisive factor for intensity change. Different shot stream causes the different value of average peening intensity. The main reason for this difference is very easy to understand, depends on: the shot size, shot speed and shot density. Increasing any single value of these parameters will lead to the increase of the average peening intensity. This increase is well understood for a single shot stream on every independent time, but as a variable, this variability is difficult to understand when have the continuous shot peening. Actually, this variability derived from the saturation curve, it depends on three factors: position, angle and time. Strictly control this three factors is necessary for any shot peeing process.

文章引用: 张 立 , 陈再良 (2015) 喷射流的变化对喷丸强度的影响。 机械工程与技术, 4, 93-100. doi: 10.12677/MET.2015.42008

参考文献

[1] 杨永红, 乔明杰, 张卫红 (2009) 条件对残余应力场的影响规律. 中国表面工程, 02, 28-33.

[2] 张平, 严瑞林 (2002) 喷丸强化中的制造控制. 航空与航天, 01, 1-5.

[3] Relation, M.G. (2011) Almen intensity to residual stresses induced by shot peening: A numerical Approach. Journal of Materials Processing Technology, 110, 277-286.

[4] 王仁智 (2012) 金属材料的喷丸强化与表面完整性论文集. 中国宇航出版社, 12, 16-40.

[5] 曾元松, 黄遐, 李志强 (2006) 先进喷丸成形技术及其应用与发展. 塑性工程学报, 13, 24-29.

[6] Kirk, D. (2013) Shot stream power and force. Shot Peener, Summer, 24-32.

[7] Kirk, D. (2011) Key terms in intensity control. Shot Peener, Fall, 12-16.

[8] Higounenc, O. (2005) Correlation of shot peening parameters to surface characteristic. Shot Peeing Application, 4, 28- 35.

[9] Petit-Renaud, F. (2002) Optimization of the shot peening parameters. Shot Peeing Application, 1, 119-129.

分享
Top