基于流体仿真的双螺杆压缩机的转子结构优化设计
The Design of Structure Optimization on Twin-Screw Compressor Rotors Based on the Fluid Simulation

作者: 姜振钢 :江南大学机械工程学院,无锡;

关键词: 圆弧包络线三维建模流体仿真分析转子型线Arc Envelope Three-Dimensional Modeling Fluid Simulation Analysis Rotor Profile

摘要:
我国国内的双螺杆压缩机型线设计水平相对于国外比较落后,转子型线是压缩机的重要零件,本文提出设计以新型圆弧包络线为基础的螺杆转子的新思路,以单边不对称摆线-销齿圆弧型线为研究对象,开发设计了新型转子型线。应用圆弧包络线构建了螺杆转子的齿廓线;利用三维软件建立了双螺杆压缩机原型线与新型线流场仿真模型,运用Fluent软件模拟了其在工作转速下压强与流速的分布规律。由仿真结果对新型线设计的合理性进行了预判,并为新型线的改进优化直至获得性能优良的双螺杆压缩机阴阳转子提供了参考依据。

Abstract: The level of designing the twin-screw compress or rotor profile in our country is relatively backward compared to foreign countries. The rotor is an important part of the screw compressor. This paper presents the new ideas based on arc-envelope to design the screw rotor. Taking the unilateral asymmetric cycloid-pins arc tooth profile as the research object, it designed a new type of rotor profile and built screw rotors with arc envelope tooth profile. It founded flow field simulation model of the original, and new twin-screw compressor rotor profile adopted the 3D software, simulated the distribution of its pressure and flow rate at operating speed with the software of Fluent. It predicted the rational of simulation results on the new designed rotor profile and provided a reference for the improvement of the new male and female twin-screw compressor rotors until getting the excellent performance rotors.

文章引用: 姜振钢 (2014) 基于流体仿真的双螺杆压缩机的转子结构优化设计。 机械工程与技术, 3, 152-159. doi: 10.12677/MET.2014.34020

参考文献

[1] 刑子文 (2000) 螺杆压缩机——理论、设计及应用. 机械工业出版社, 北京.

[2] 范春艳 (2010) 试论螺杆压缩机发展现状及应用. 化学工程与装备, 9, 186-187.

[3] 熊伟, 冯全科 (2005) 螺杆压缩机研究现状与热点. 流体机械, 3, 30-32.

[4] 喻志强, 林子良, 于洋 (2006) 国内螺杆压缩机的发展研究. 通用机械, 8, 18-19.

[5] 邢子文, 吴华根, 束鹏程 (2007) 螺杆压缩机设计理论与关键技术的研究和开发. 西安交通大学学报, 7, 755- 763, 810.

[6] 徐健, 余宾宴, 余小玲, 等 (2012) 螺杆压缩机转子型线设计方法. 压缩机技术, 2, 1-6.

[7] 潘小强 (2004) CFD软件在工程流体数值模拟中的应用. 南京工程学院学报自然科学版, 2, 62-66.

[8] 朱红钧, 林元华, 谢龙汉 (2010) FLUENT流体分析及仿真实用教程. 人民邮电出版社, 北京, 39-42.

[9] 周志宏, 李勇 (2008) 双螺杆压缩机转子圆弧及圆弧包络线型线的几何构造. 机电产品开发与创新, 6, 129-130.

[10] 王文军, 平雪良, 龚玉玲, 马仙龙 (2008) 压缩机螺杆转子型线逆向设计法. 机床与液压, 36, 75-77.

[11] 马仙龙 (2008) 基于NURBS的双螺杆压缩机转子型线研究. 江南大学, 无锡.

[12] Stosic, N., Smith, I.K. and Kovacevic, A. (2004) Estimation and control of heat transfer in screw compressor rotors. ASME 2004 International Mechanical Engineering Congress and Exposition, Anaheim, 13-19 November 2004, 441- 446.

[13] Stosic, N. and Smith, I.K. (2001) Rotor interference in screw compressors. In: Yu, Y.Z., Ed., Proceedings of the 3rd International Compressor Technique Conference, Xi’an Jiaotong University Press, Xi’an, 134-142.

[14] Fouflias, D., et al. (2009) CFD Predictions of cas-cade pressure losses due to compressor fouling. ASME Turbo Expo 2009: Power for Land, Sea, and Air, Orlando, 8-12 June 2009, 99-108.

[15] 吴宝志 (1985) 螺杆式制冷压缩机. 机械工业出版社, 北京.

[16] L.林德 (1986) 螺杆压缩机. 机械工业出版社, 北京.

[17] FLUENT Inc. (2003) FLUENT 6.1 Documentation. FLUENT Inc., New York.

分享
Top